Installing Throttle Positioning Sensors
. Опубликовано: 8 авг 2016. Today we're replacing, and adjusting, a throttle position sensor. The sensor detects the opening and closing of the throttle valve and feeds that info to the vehicle's computer. This was performed on a 1997 Nissan Maxima.
15 товаров по поисковому запросу install throttle position sensor в категориях Авто и мото, Датчики положения дроссельной заслонки. Бесплатная доставка или более Только в мобильном Местный Возврат More. Датчик положения дроссельной заслонки Throttle Position Sensor (TPS). Датчик положения дроссельной заслонки расположен на корпусе узла дроссельной заслонки. Служит для измерения степени открытия дроссельной заслонки. Датчик положения дроссельной заслонки. Чувствительный элемент датчика положения дроссельной заслонки представляет собой потенциометр, ось которого жёстко связана с осью дроссельной заслонки. На питающие выводы потенциометра подается опорное напряжение +5 V и 'масса', а подвижный контакт датчика является сигнальным.
Check with your vehicle's repair manual for testing parameters. »»» Subscribe: »»» Facebook: facebook.com/pages/Carsntoys/05993 »»» Website: carsntoys.net »»» Music: Club Thump by Gunnar Olsen.OTHER VIDEOS THAT MAY INTEREST YOU. Wheel bearing replacement with basic hand tools: - Choosing the best oil filter: Wix XP / Amsoil / Royal Purple. Touch Screen car radio install: Tools Used: Safety Glasses Phillips Screwdriver Digital Multi Meter Note: Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles. Such as, safety glasses, jack stands, no loose clothing, etc. No guarantee or warranty is implied.
Use the information in this video at your own risk. Publication, reproduction or distribution of this film is strictly prohibited. Месяц назад Hey man I have a nissan 2000; I changed everything and the computer, then a relay located next to the radiator but the radiator was broken so It was replaced and it started to shot off after it warms up.
I think it was running pretty hot before and now it is not running too hot because the radiator replacement. And at time when I was in trafic and the car would probably get hot it idel with hier RPMs and now it does not it idels then dies. Raul paz discografia download.
If I press on the gas right before it wants to die it recovers and then does it again. 7 месяцев назад I replaced the TBS on my 2001 Nissan Maxima but I’m having horrible problems, I adjusted the sensor to the old position started the car and it started with no problem.
But when I try to rev it, it won’t go past 2000rpm and out of a sudden you hear a bang or pop in the engine I let go of the accelerator and the engine goes down to 1000rpm and idles normal I try driving it but can’t accelerate or the engine try’s to stall past 2000 rpms I checked for direct current but the sensor only gives 0.11 while on the throttle body but if I unscrew it off the throttle it reads perfectly fine I screw it back in the throttle and it only reads 0.11 again. Any help would work thanks.! 7 месяцев назад i have 2000 nissan sentra gxe.
I clean the throttle body and now the it is idling high. I replace it with a used one but same issue. I intalled the oreginal idle control valve. I notice the the thorrtle is open more the what it should be. I adjusted the the screw to retard the idle, it did help a little. I notice that can press the throttle back a little and it idles like it should, if i let go, it spring back. Im startting to suspect its the thorrtle position sensor.
Would you be able to give ur expert advise on this issue? Год назад Hey brother I loved the info you gave.
I am having problems with a 2001 Hyundai Sonata 2.4L 4 cyl. What's going on is when it sits for a minute and then I restart and try and go it acts like its not getting gas but after about a minute or longer it runs fine like nothing is wrong. I finally got the ✔️Engine light to come on so I plugged in the Autel OBO II which said it was the TPS. Now I have the manual but my book says to use MV and you used just volts on meager. I have been searching all over internet about this but can't find anything. So do you have the info I need to check the sensor.
Have a Good Day!!!